The Klipsch midrange drivers are a hot topic of discussion among Klipsch enthusiasts. There is a lot of mis-information about them circulating on the internet and various audio forums; even the Klipsch forum.
Often stated by PWK, "the midrange is where we live". Our ears are most sensitive to the frequencies in this region.
The information presented here has been assembled by me from 1978 to the present. It has been gathered from conversations with Klipsch engineers, Klipsch documentation, Atlas engineering and documentation, Electro-Voice documentation and Paul W. Klipsch via the Dope from Hope publications.
Hopefully, this will help the Klipsch enthusiast better understand the different drivers used in the vintage Heritage speakers and make it easier to separate fact from fiction. Up until late 1981, the Klipschorn, Belle, LaScala, Cornwall and Heresy all used the same treble section - K-55-V midrange driver and K77 tweeter. The Cornwall went through several midrange drivers from late 1981 through 1983. Those drivers are not discussed here to avoid confusion.
In November of 1961, the Atlas manufactured PD-5VH (K-55-V) was introduced in the Klipsch line. This driver was patterned after the famous Western Electric 555-W driver that was designed for large format horns and was used in movie theatres. The diaphragm/phase plug of the K-55-V is a modern carry-over of the Western Electric 555-W design. This is a very robust Alnico magnet driver utilizing a 2" phenolic diaphragm and spring loaded push terminals for wire attachment. Depending on back air chamber configuration, it can be used in different applications. Information stating that the Atlas PD-5VH (K-55-V) was originally designed for siren use is not entirely true. Atlas made two versions - one with a 3-hole backplate which peaks the driver in the 1 to 3K range for siren use, as well as a 7-hole backplate version which offered the +/- 5dB 400 - 6500Hz frequency response as found in the Klipsch K-55-V. This version of the K-55-V was used from 1961 through 1979. Paul Klipsch developed the K-400 self-equalizing exponential horn around this driver.
In January of 1979, Klipsch Chief Engineer at that time, Gary Gillum, modified the K-55-V by nesting the cone phasing plug to help improve the frequency response between 4 and 5kHz. This modification smoothed response across the bandwidth. Solder terminals replaced the push terminals on these drivers to differentiate between the two K-55-V versions. The nested cone version was introduced to the line in late March of 1980. Production was short lived, however, as Atlas had trouble keeping the modified phasing plug in place. Driver failures were reported and in late '82 - early '83, Atlas was in the process of changing the magnet structure from Alnico to ceramic. There were back air chamber differences between the Alnico and the ceramic magnet assembly which altered the frequency response. The ceramic magnet driver would not go down to 400Hz which was required for use in the Klipschorn.
By late 1983, the K-55-V was replaced by the Electro-Voice manufactured K-55-M. The K-55-M was a ceramic magnet driver with a 2" phenolic diaphragm and nested phasing plug. Frequency response was similar to the Alnico nested phasing plug Atlas K-55-V. There were different crossover networks - herein referred to by their correct name - balancing networks, used with this driver. According to Klipsch, when the prototype driver was tested, the sensitivity was greater than that of the Atlas K-55-V. Balancing networks were developed around the prototype and put into production. At some point in the K-55-M production, the sensitivity changed and became closer to that of the Atlas K-55-V. In 1989, new balancing networks were developed to compensate for this change in the driver output. Sensitivity variations were not unique to the midrange E-V drivers. For years, Klipsch matched sensitivity of the K-77 E-V manufactured tweeters as well as Atlas manufactured K-55-V midrange drivers in order to have balanced pairs for speaker production. This is why it is not recommended to mix-and-match drivers and balancing networks. When Klipsch manufactured these speakers, sequentially numbered pairs were matched acoustically so they would perform uniformly. Swapping components invariably leads to a degradation in performance, regardless of what you read in the various audio forums and what some aftermarket parts suppliers tell you. Electro-Voice discontinued production of the K-55-M in 2000.
When Electro-Voice discontinued the K-55-M, a search for a replacement driver ensued. Enter the K-55-PH. According to Klipsch Chief engineer Roy Delgado, this driver was a copy of the Electro-Voice K-55-M. It was never used in production as only a few were ever produced. The K-55-PH should not be included in the list of midrange drivers as it was never used in production. However, when Klipsch sold the inventory to an aftermarket parts supplier and it was offered as a LaScala replacement driver, questions were asked. It was initially reported to be a copy of the Atlas driver, which is not the case. It is discussed here only because it made it into the market. It is not a direct replacement for any of the production midrange drivers.
When a replacement for the K-55-M could not be found, Klipsch went back to Atlas. Atlas was willing to make the PD- 5VH, but not with the nested cone phasing plug. This driver has the solder lug terminals as did the nested cone K-55-V. Klipsch designated this driver as the K-55-X. Many aftermarket part suppliers state that this current version of the Atlas PD-5VH is the same as the old push connector K-55-V. The current production Atlas PD-5VH is not identical to the original version. The frequency response drops off significantly at 4100Hz. The original version had a dip between 4-5kHz, but recovered and went out to 6500Hz. The original balancing networks had a 6k crossover point. When Klipsch tested the new PD-5VH and discovered the change in the frequency response, the crossover point was lowered to 4500Hz. This is why the new driver became the K-55-X and not K-55-V again. According to Atlas, the diaphragm underwent a change which resulted in the frequency response variation from the original version. Klipsch does not sell the K-55-X as a K-55-V replacement. You need an AK-4 balancing network in a Klipschorn to use this driver.
WARNING: the new replacement PD-5VH diaphragms which are available should not be installed in a speaker system with a 6k balancing network. Installing this diaphragm in an older unit takes it from a 6500Hz driver to a 4100Hz driver. You will be told by various parts dealers that the K-400 horn extends the frequency response to 6k so the new driver works. This is absolutely false. If you have a new driver or have replaced the diaphragm in your old unit with a new one, you can verify this yourself. Disconnect your tweeter, play a 5k and 6k tone. You won't hear much from the midrange. Play an 8k tone. You will hear that because of the frequency response bounce back with these drivers. The horn does not significantly extend the 4 to 6k frequency response. You will have a large hole in your speaker frequency response using the new driver or new diaphragms in your older drivers when using the original balancing networks. I bet the parts dealer never told you about that! Phenolic diaphragms, which were used in the older drivers, RARELY go bad. They don't get "hard" with age if in a normal environment. If a speaker is well cared for, the diaphragms will last a lifetime. Diaphragms can be affected by heat, extreme cold, tropical humidity, etc. Use common sense; if the environment is comfortable for you, it should be fine for your speakers.


From bottom left, clockwise - K-55-V, used from November, 1961 till March, 1980. K-55-V w/nested cone phasing plug, used from March, 1980 till October, 1983. K-55-M used from October, 1983 till 2000. K-55-X used from May, 2001 till 2024. The K-55-V and K-55-X were manufactured by Atlas. The K-55-M was manufactured by Electro-Voice. All of these drivers are 16 ohm.

Same order as photo at left.

This driver is a copy of the Electro-Voice manufactured K-55-M. It was never used in production as only a few were able to be manufactured. This information provided by Klipsch Chief engineer Roy Delgado. My samples indicate a slightly different sound likely due to frequency response variations and a slightly higher output than the K-55-M. The K-55-M is on the left, the K-55-PH is on the right in the photo above.
The A-55-G series of midrange drivers are developed by John Allen and produced in the Philippines. The current version is the A-55-G/2.5. The exterior design resembles the Electro-Voice K-55-M. These drivers are marketed as replacements for and an up-grade from the K-55-V and K-55-M midrange drivers.
Many have purchased these drivers and are satisfied with them. The purpose of this section is to provide information regarding the differences between this product and what the factory originally installed. I get questions about these drivers quite frequently and feel it best to point out the deviations from factory installed drivers and provide photos for reference. Based on the physical and electrical differences from the original drivers, I can't agree with calling them replacements. Yes, they screw onto the back of the Klipsch designed horns, but there is a bit more to it than that. It is up to the reader to decide if he/she wants to use them. These drivers are not approved by Klipsch engineering as replacements.
Physical difference.
There is a larger driver exit throat opening than the Klipsch designed horn throat entrance. This creates a mismatch between driver and horn. Sound waves exiting the driver throat hit the restriction caused by the smaller opening in the horn throat entrance. This can cause turbulence, added distortion, impedance changes, and frequency response anomalies. You need a smooth transition (flow) from driver to horn to get the best performance out of a particular driver/horn combination. Think of the driver/horn combination as a intake manifold/cylinder head combination on an internal combustion engine. The ports from the intake manifold are matched to the cylinder head intake ports with precision. This allows the fuel vapor to achieve a smooth, uninterrupted flow into the cylinder head which improves fuel economy as well as engine performance. It doesn't matter if we are talking fuel vapor or sound waves, it's all about smooth flow when transitioning between two components. There is information about the importance of matching driver/horn combinations on the internet for those interested.
Electrical properties
Original networks are designed around 16 ohm midrange drivers. The A-55-G series of drivers are 12 ohms.


.


This website uses cookies. By continuing to use this site, you accept our use of cookies for analytic purposes.